GE6162-ENGINEERING PRACTICES LABORATORY REQUIREMENTS
Hi welcome to allinfo2017.In this post we just going to discuss about the requirements of the GE6162-ENGINEERING PRACTICES lab i.e Engineering Practices Lab.
where GE6162-ENGINEERING PRACTICES lab is divided into Groups based on the Department.They are
i) Group A
ii)Group B
i) Group A
In this group it is categorized by the department of Civil & Mechanical Engineering,i.e this group content are fully designed by this department based experiments.ii)Group B
In this group it is categorized by the department of Electrical & Electronics Engineering,i.e this group content are fully designed by this department based experiments.where this lab categorized by two groups A & B.instead this group in this blogger going to give the details about the group B category only.
Let us see the GE6162 lab requirements.
again the group B is divided into 2 parts.they are
GE6162-ENGINEERING PRACTICES Lab
a) ELECTRICAL ENGINEERING PRACTICE
Residential house wiring using switches, fuse,
indicator, lamp and energy meter
let us see this is the experiment which requires
i)Switches - SPST -1,SPDT
ii) Fuse - Protective devices -10 amphs
iii)Indicator - 1 Nos
iv ) Lamp -Incandescent Lamp - 5 Nos
Iv)Energy Meter - 1 Nos
Fluorescent lamp wiring
i)Fluorescent Lamp - 1 Nos.
ii)Ballast Circuit - 1 Nos.
iii)Starter - 1 Nos.
Iv)Multi core Wire as per required
Stair case wiring
i)SPDT Switch - 2nos
ii) any Loads i.e is Lamp load - 1 Nos
Measurement of electrical quantities –
voltage, current, power & power
factor in RLC
circuit
i)Voltmeter 0-230v -1No
ii)Ammeter 0-10 amps -1No
iii)Power Meter -1000watts -1Nos
iv)Power factor meter - 1No
v)Rheostat Loaad - 1 No
vi)Inductor Load- 1 No
vii)Capacitor load -1No
Measurement of energy using single phase
energy meter
i)Voltmeter 0-230v -1No
ii)Ammeter 0-10 amps -1No
iii)Power Meter -1000watts -1No
iv)Energy meter Analog/Digital - 1No
Measurement of resistance to earth of an
electrical equipment
i)Voltmeter 0-230v -1No
ii)Ammeter 0-10 amps -1No
iii)Power Meter -1000watts -1No
Emergency Lamp Set - 1No
Iron Box - 1No
Fan with regulator set - 1No
b) ELECTRONICS ENGINEERING PRACTICE
Study of Electronic components
and equipments – Resistor colour coding
measurement of AC signal
parameter (peak-peak, rms period, frequency) using CRO
i) Resitor Box as much as required.
ii)CRO or Spectrum Analyzer -1No
Study of logic gates AND, OR,
XOR and NOT
IC7400 AND gate - 1No.
IC7432 OR gate - 1NO.
IC7486 XOR gate - 1 No.
IC7404 NOT gate - 1No.
Generation of Clock
Signal
generating clock Pulse using IC555 or by using IC741 opamp
each 1 No.
Soldering practice –
Components Devices and Circuits
– Using general purpose PCB
Asserted components such as resistors,Capacitor and other components are used for soldering and de soldering practice.
Measurement of ripple factor
of HWR and FWR
Half Wave Rectifier and Full Wave Rectifier using Diode - 4 Nos.
CRO - 1 No,
Resistor - 1 No
Capacitor - 1 No
Inductor - 1 No
No comments:
Post a Comment